Forum Post: Modify PI
Is there any procedure in power rail track to change the horizontal or vertical PI with out disturbing the 1st tangent angle.
View ArticleForum Post: Modify the transition
I have around 40 curves in my 100km alignment. I have considered clothoid as a transition. Now i want to change cubic parabola western Australia for all the 40 curve transitions. Is there any simple...
View ArticleForum Post: Cross section template with drain
I have created template with fixed drain dimensions. Now as per client requirement drain has it separate vertical alignment as per drainage design. Can i integrate the my track alignment and drainage...
View ArticleForum Post: Edit Element by Graphically
Please find the attachment. Normally i use edit alignment command to trim element. As shown in the attachment i used to measure graphically which ever length i want to trim and that value i subtract...
View ArticleForum Post: RE: Modify PI
In Define Horizontal Curve Set usee the Define By Direction and Distance from Previous PI option. A similiar option is avaiable for vertical. Regards, R. W. Bradshaw
View ArticleForum Post: RE: Modify the transition
I am assuming that you want to maintain the transition length, so the following will work: 1. Create a horizontal report and use the DataCollection/HorizontalAlignmentToTIW.xsl and save the results 2....
View ArticleForum Post: RE: Edit Element by Graphically
Use Horizontal Elements > Cut to cut an alignment at a specific point. Then use use Horizontal Elements > Delete to delete the element that you don't want. Regards, R. W. Bradshaw
View ArticleForum Post: RE: Extra clearance
You will need to modify each radius and transition length to increase the offset, by using the Define Horizontal Curve Set command. Regards, R. W. Bradshaw
View ArticleForum Post: RE: Minimum Track Center Distance at Curve
You will need to modify each radius and transition length to increase the offset, by using the Define Horizontal Curve Set command. Regards, R. W. Bradshaw
View ArticleForum Post: RE: Cross section template with drain
You can do that with Point Controls within Corridor Modeling. R. W. Bradshaw
View ArticleForum Post: RE: Simulation
I would suggest using the Swept Envelope Analysis add-in. Regards, R. W. Bradshaw
View ArticleForum Post: How to display existing track gauge at 5m interval in the model?
Hello all I was hoping if someone could help me with displaying the existing track gauge in BRT. I have a two line railway on a curve both of which has 40mm of cant on a track gauge of 1435mm. I want...
View ArticleForum Post: How do you get the roadway designer to deal with CANT?
Hi, To summarise; needing to create a 3D string which represents (for example) the edge of a station platform - set co-planar to the running rails. Currently playing around with templates and roadway...
View ArticleForum Post: RE: How do you get the roadway designer to deal with CANT?
Angus Couple of things to check Do you have a cant alignment designed in BRT/PRT/InRail as a child alignment of your Horizontal Alignment in your alg. (see images) The next thing to check is if you...
View ArticleForum Post: Unique curve numbering for curves
May i assign unique curve number for each and every curve.
View ArticleForum Post: Existing track geometry at regular (5m or 10m intervals)?
Is it possible for BRT to produce a report that provides the existing track (CL) geometry at regular intervals (preferably 5m or 10m) rather than at the regression points?
View ArticleForum Post: RE: Existing track geometry at regular (5m or 10m intervals)?
Angus Yes I think we can do this OK This method probably works better if you can bring your existing Right Hand and Left Hand rails in to your ALG. This means BRT can report off the actual 6ft interval...
View ArticleForum Post: RE: How to display existing track gauge at 5m interval in the model?
One way is: display rail in 3D create transverse feature (design surface) graphic only import previsously created features as breakline in a surface annotate feature "slope length"
View ArticleForum Post: import file
Respected Sir, how to import file in Bentley powe rail track V8i series4. I have three files 1. ALG FILE 2 .DTM FILE 3. XIN FILE Thank you Sir, Prashant Sharma Prashantcivil.sharma@gmail.com
View Article