Forum Post: RE: translate from PowerRailTrack to MX
Some additional info: all my vertical alignments in BPRT are defined with circular curves, and in the project settings for MX I also set the vertical curve to circular. After importing the LandXML (no...
View ArticleForum Post: RE: translate from PowerRailTrack to MX
LandXML supports parabolic and / or circular vertical curves. I am aware of an issue with circular vertical curves with a negative radius. The radius should aways be positive. If you send me the .xml,...
View ArticleForum Post: RE: Alignment plan display in 2D in Microstation
Use Geometry > View > Horizontal Annotation and check on Planarize. Regards, R. W. Bradshaw
View ArticleForum Post: RE: translate from PowerRailTrack to MX
See attached files: the original .alg and exported LandXML, v.1.1/1.2 (Please visit the site to view this file) landxml (Please visit the site to view this file) .alg Regards, Gerbert Verheij
View ArticleWiki Page: Rail Design - Wiki
Because the Rail Track products share a majority of their commands with the Road Design products, visit the Road and Site Design Support Solutions for more content. You can also visit the Rail Track...
View ArticleForum Post: RE: translate from PowerRailTrack to MX
I would try the following and see if MX can see the data as circular vertical curves rather than parabolas. Go into NOTEPAD and search and remove the sign from all of the radius fields: Search for...
View ArticleForum Post: RE: Collinear Vs Tangency
In fact "non collinear" means that tangents are not the same, within a tolerance 0.1" (0.5mm for coincident). So you can get a non collinear report between all types of elements not only straights.
View ArticleForum Post: RE: Missing levels in InRail Plan and Profile generator
Do you mean levels that contain element ? Did you check nesting depth ? Any filter ?
View ArticleForum Post: RE: HORIZONTAL REGRESSION FROM IMPORTED COORDINATES
HI Giannis, did you find your way using the txt file ?
View ArticleForum Post: RE: Alignment plan display in 2D in Microstation
Hi Richard,Thanks for the reply; I have noticed that, your solution will solve (check on Planarize) the issues only in the view-horizontal annotations. But, when I right click and view the alignment...
View ArticleForum Post: Horizontal and Vertical Check Integrity Addin
Dear all, I have formatted my C-Drive and re-installed Power Rail Track v08.11.07.536 and re-registered it. Later I found in reports that both Horizontal check integrity and vertical check integrity...
View ArticleForum Post: RE: Horizontal and Vertical Check Integrity Addin
Goto Tools > Application Add-ins and check on Horizontal and Vertical Elements. You may need to look at the entire list and add in additional add-ins. Regards, R. W. Bradshaw
View ArticleForum Post: RE: Alignment plan display in 2D in Microstation
Then goto Geometry > Utilities > Assign Elevations and set the elevation of the horizontal alignment to zero. This has the same affect as the planarize option, except that the elevation on the...
View ArticleForum Post: RE: Multiple Vertical Alignments On A Single Profile
I would say that interval is honoring the station lock setting. So it could be even of 10m and not first point + 10m. But I didn't check yet.
View ArticleForum Post: RE: Alignment plan display in 2D in Microstation
Hi Richard, Thanks for your suggestion, that helped me to solve my problem.
View ArticleForum Post: Cut/Fill - need vertical offset
Hello! When cut and fill are calculated they are calculated from rail level. But it must be from earth bed. How can I set a vertical offset?
View ArticleForum Post: RE: Cut/Fill - need vertical offset
Hi Aleksandar, could you clarify ? I don't understand your issue. Is it on profile ?
View ArticleForum Post: RE: translate from PowerRailTrack to MX
Hi Gerbert, If your client has MX SS4 edition with the "OpenRoads technology he can also import the ALG file. Regards, Christiaan
View ArticleForum Post: Missing Point Symbols
Hi, I'am missing the point Symbol option in Railtrack see image, where can I find these setting or is this only available in the latest version? Using: BPRT 08.11.07.615 Regards, Christiaan
View Article