Forum Post: RE: HOW TO CALCULATE ELEVATION MANUALLY IN VERTICAL CURVE( CUBIC...
Not sure to well understand the request. You can annotate proposed, do tracking on profile/plan to get elevation wherever you want. You can annotate low/high points on the profile using view geometry...
View ArticleForum Post: RE: Bentley rail track did't open either cad or microstation?
The latest SS2 (08.11.09.685) should work on top of MicroStation SS3. Check the readme chm in C:\Program Files (x86)\Bentley\PowerRailTrack V8i\PowerRailTrack
View ArticleForum Post: RE: Products under OpenRail
Under Openrail Brand you can find Rail Track (Bentley or Power Rail Track) and Power Rail Overhead Line
View ArticleForum Post: RE: Move geometry file
how to move corresponding turnouts and crossovers along with strings..?
View ArticleForum Post: RE: Platform Crossfall Template
Thanks jpln From what I understand, you use NULL(L) and NULL(R) to set the slopes at 1:80 based off the back of BACK(L) and BACK(R) respectively. These are null components and will not be "created"...
View ArticleForum Post: RE: Platform Crossfall Template
No you don't need 2 corridors. It is the general case where you have 2 corridors for any reason and it also works if corridors are not parallel. Looking again on your post concerning 1:80 and 1:40 it...
View ArticleForum Post: RE: Platform Crossfall Template
Thanks jpln That sounds interesting. I have the template in the image below that draws a 1:80 and 1:40 line from each side of the back of coper to form a point where both slope conditions will be...
View ArticleForum Post: Cant - Double track
Hi, I have some difficulties with my 3D model there for I use an ALG file for the track with Cant. When I run the model track 1 is correct and track 2 has some strange things see image, Any help will...
View ArticleForum Post: RE: Cant - Double track
I also tried to ad the cant with a *.txtf and that won't work ether. When adding a single track template to Track 2 it works fine? Please help
View ArticleForum Post: RE: Platform Crossfall Template
I would suggest you, to create 3 slope template. 1. Create center platform point CPP by horizontal distance from some BACK point = 0.5*(BACKL to BACKR) 2. Create 2 NULL points (NULL-1 slope from...
View ArticleForum Post: RE: Beta version PowerCivil "OpenRail" When?
Hi Ian, Is there a Beta program for "OpenRail" and is it possible to join? Thanks in Advance. Regards, Christiaan
View ArticleForum Post: RE: Platform Crossfall Template
Aleksandar I followed all your steps apart from the last one. I now have a template that will have the shallowest slope of 1:80 and if the adjacent rail level is raised, the slope steepens to...
View ArticleForum Post: Clearance in Track Plane Report Question
All Am looking for some information on what kind of report to use or even help with developing a stylesheet in PRT SS2. My goal is to be able to generate a report for horizontal and vertical offsets...
View ArticleForum Post: İ can't show the Turnout in Profile
Hi everyone, I created a diamond crossing and 4 simple turnouts. For track-2, it show both of turnuots in profile. But for track-1 it just shows 1 turnout. I couldn't understand why. Can you help me?...
View ArticleForum Post: RE: Cant - Double track
hi Christiaan, a bit difficult to analyze from the picture. template/corridor (IRD) used and geometry (ALG) is required to have a look. Or ALG+DGN if it is Rail Track SELECTseries 4
View ArticleForum Post: RE: İ can't show the Turnout in Profile
Did you used the connexion editor? If yes does everything look good?
View ArticleForum Post: RE: İ can't show the Turnout in Profile
I created the turnouts alone (M03, M04, M05 and M06). And then connected them by connection editor (M03-M06, M04-M05). After annotation, M04-M05 turnouts are annotated in profile like on the picture....
View ArticleForum Post: Problem in curve widennig
Hi Everyone, I am using PRT series2.When i am applying curve widening and point of control to both line(up and down line), for RH curve it is fine but wherever LH curve and Track distance is more than...
View ArticleForum Post: Two Elements on Importing into SS4
All I am in PRT SS4 (have now switched as I have a W10 machine) and am looking for some help with alignments/ cross sections When I import my alignments from my ALG file into the DGN using the "Import...
View Article
