Forum Post: which platform will support bentley rail track?
i have installed microstationss3 & it's working very well but at the same time & same pc installed rail track ss2, rail track never open. how can i do now?
View ArticleForum Post: Bentley rail track did't open either cad or microstation?
How to open Bentley rail track ss2 or which platform will support it, i tried Cad 2009 & Microstation ss3 but failed.
View ArticleForum Post: HOW TO CALCULATE ELEVATION MANUALLY IN VERTICAL CURVE( CUBIC...
HERE I ATTACHED THE BRT OUTPUT AND PLEASE SUGGEST ME THE EXACT METHOD TO FIND THE ELEVATION WHICH WAS ALREADY GENERATED THROUGH BRT.
View ArticleForum Post: HOW TO CALCULATE ELEVATION MANUALLY IN VERTICAL CURVE( CUBIC...
HERE I ATTACHED THE BRT OUTPUT AND PLEASE SUGGEST ME THE EXACT METHOD TO FIND THE ELEVATION WHICH WAS ALREADY GENERATED THROUGH BRT.
View ArticleForum Post: Turn off Automatic Surface Creation
All I am working in PRT SS2 I am working in the Roadway designer, trying to apply quite a complex template to a multi alignment corridor. I have pressed a button or ticked a box or set a preference or...
View ArticleForum Post: RE: Turn off Automatic Surface Creation
If "Surface generated" means the surface is triangulated then disable "Triangulate Surface" in Surface Creation
View ArticleForum Post: Create Cross section
In power rail track software I am unable to locate Create Cross section under Evaluation >> Cross Section, previously which was available in ss2 version. But in SS4 version create cross section...
View ArticleForum Post: RE: Turn off Automatic Surface Creation
Thanks for this, but I dont think this is quite what I am looking for. In the Roadway designer, every time I made a change to my corridor using any one of the tools in the "Corridor" Drop down menu...
View ArticleForum Post: RE: Turn off Automatic Surface Creation
ok, in that case go to Variable manager and uncheck "Dynamic Actualize design Graphic" (or similar - I have it here in German only).
View ArticleForum Post: RE: Turn off Automatic Surface Creation
Thank you! This was the problem! My machine isnt powerful enough to dynamically reload graphics. I usually make all my changes and then click "process" and go for a cup of tea! Cheer hubertusb
View ArticleForum Post: RE: Create Cross section
These are the same tool only available in different locations. I think there are some updates to the tool in SS4, but not too many changes from SS2 See the thread below...
View ArticleForum Post: RE: Create Cross section
The functionality of both the tools are not same. The tools >> corridor >> cross section menu only works when corridors are made first. I am not using corridors. I want same functionality...
View ArticleForum Post: Platform Crossfall Template
All I am trying to make a template for an island platform to deal with the drainage crossfall. Here is what I have I have two tracks either side of a proposed island platform with a design Horizontal,...
View ArticleForum Post: RE: Platform Crossfall Template
See attached for info (Please visit the site to view this file)
View ArticleForum Post: RE: Platform Crossfall Template
Create one component (not end condition) by 3 points. Left edge / Center point (drain point, controled by slope to Left edge, and slope to Right edge) / Right edge
View ArticleForum Post: Position of Templates after change of stationing
Hello, is it necessary to manually change positions of templates when I change stationing? I would like to froze position of start/end templates. Is it possible? Or is it necessary to manually change...
View ArticleForum Post: RE: Platform Crossfall Template
Aleksandar Thanks for this - this is what I was thinking, but it ended up putting the drain in a zigzag path based on the adjacent rail heights I have done what you said only with a bit of a change. I...
View ArticleForum Post: RE: Position of Templates after change of stationing
Please could you provide product version and workflow? If you change the stationing the template drops locations XY don't change. So if the template drop start at station 40 when station at beginning...
View ArticleForum Post: RE: Platform Crossfall Template
So I assume you've got 2 corridors, one for left track and one for right track. What I suggest is to create a null point to define the 1:80 slope from BACKL to NULLL and another one for the right slope...
View ArticleForum Post: RE: Create Cross section
Create Cross Section is available from corridor toolbar but doesn't require to have a corridor. It is the only way to create cross sections and is similar than SS2 with some few differences (scale,...
View Article